User avatar
petermontg
Posts: 610
Joined: Sat Jun 26, 2010 7:51 am
Location: Ireland.

Audax RH5 manual

Post: # 15093Unread post petermontg
Mon May 23, 2011 6:58 pm

If someone could point me in the right direction for one, I'd greatly appreciate it.



Regards
Peter Montgomery
+353(0)894926271
peter(at)petermontgomerymastering.com

Stereo cutter head wanted. Send email or smoke signals.

User avatar
petermontg
Posts: 610
Joined: Sat Jun 26, 2010 7:51 am
Location: Ireland.

Re: Audax RH5 manual

Post: # 15242Unread post petermontg
Tue Jun 07, 2011 6:37 am

petermontg wrote:If someone could point me in the right direction for one, I'd greatly appreciate it.



Regards
problem solved
Peter Montgomery
+353(0)894926271
peter(at)petermontgomerymastering.com

Stereo cutter head wanted. Send email or smoke signals.

User avatar
folk
Posts: 35
Joined: Sat Nov 21, 2009 4:09 pm
Location: portland

Post: # 15359Unread post folk
Wed Jun 15, 2011 10:22 pm

did you find a manual? We need to service ours and I'm wondering if it's possible to DIY

User avatar
petermontg
Posts: 610
Joined: Sat Jun 26, 2010 7:51 am
Location: Ireland.

Post: # 15519Unread post petermontg
Wed Jun 22, 2011 12:16 pm

folk wrote:did you find a manual? We need to service ours and I'm wondering if it's possible to DIY
there wasnt a manual as such, just a small leaflet with basic info on the head

i have been meaning to post it here but keep forgetting. ill do it soon.
Peter Montgomery
+353(0)894926271
peter(at)petermontgomerymastering.com

Stereo cutter head wanted. Send email or smoke signals.

User avatar
JayDC
Posts: 849
Joined: Sat Jan 13, 2007 5:45 pm
Location: Philadelphia

Post: # 15524Unread post JayDC
Wed Jun 22, 2011 1:18 pm

get on it... if u got info, there are new people that need help wif dat head..
generally its for reproduction.. but i like to play wif it sometimes.. :P

User avatar
petermontg
Posts: 610
Joined: Sat Jun 26, 2010 7:51 am
Location: Ireland.

Post: # 15580Unread post petermontg
Fri Jun 24, 2011 10:21 am

IMPEDANCE: 8 - 15- 500 OHMS.

SENSITIVITY: APPROXIMATELY 1.8 WATTS AT 1000 CYCLES FOR 6.3 CM/SEC PEAK RECORDED VELOCITY.

FREQUENCY RESPONSE: +2 DB FROM 1000 TO OVER 13,000 CYCLES. FROM 1000 DOWN TO 30 CYCLES, BUILT-IN ATTENUATION PER R.I.A.A CURVE WITHIN 3 DB.

DISTORTION: 1.2% AT 1000 CPS.

MOUNTING: UNIVERSAL MOUNTING FOR MOST LATHES. 1 1/8" BETWEEN MOUNTING HOLES OF CUTTER.

STYLUS:
SHORT SHANK 5/8" OVER-ALL STYLUS LENGHT.

its not much, but thats all the info that came with the head.

hope it helps somebody.

regards
Peter Montgomery
+353(0)894926271
peter(at)petermontgomerymastering.com

Stereo cutter head wanted. Send email or smoke signals.

User avatar
JayDC
Posts: 849
Joined: Sat Jan 13, 2007 5:45 pm
Location: Philadelphia

Post: # 15588Unread post JayDC
Fri Jun 24, 2011 4:01 pm

wow.. what a great head.. good spec's.. going to have to find one of those
generally its for reproduction.. but i like to play wif it sometimes.. :P

User avatar
petermontg
Posts: 610
Joined: Sat Jun 26, 2010 7:51 am
Location: Ireland.

Post: # 15593Unread post petermontg
Sat Jun 25, 2011 10:22 am

robert van dyke has a few of them for the 250USD, perfect condition didnt need a rewire or remagnatised.
Peter Montgomery
+353(0)894926271
peter(at)petermontgomerymastering.com

Stereo cutter head wanted. Send email or smoke signals.

User avatar
JayDC
Posts: 849
Joined: Sat Jan 13, 2007 5:45 pm
Location: Philadelphia

Post: # 15598Unread post JayDC
Sat Jun 25, 2011 1:19 pm

pm me w/ info thanks..
generally its for reproduction.. but i like to play wif it sometimes.. :P

Post Reply