Search found 507 matches
- Thu Dec 11, 2014 10:58 am
- Forum: Experimenters' & Innovators' forum
- Topic: Caruso RIAA pre-amp Power Supply?
- Replies: 15
- Views: 4010
Re: Caruso RIAA pre-amp Power Supply?
Hi All, I too am struggling, not so much the concept, more the practicality and application. I've recently built a Pulse Width Modulator DC Output Kit for the Stylus Heater Element of my CutterHead, and found it difficult due to chronic arthritis and failing eyesight. I've seen advertised from reput...
- Tue Dec 02, 2014 12:36 pm
- Forum: Secrets of the Lathe Trolls
- Topic: Torque Requirements
- Replies: 2
- Views: 653
Re: Torque Requirements
Thanks for the input Mark, the 10 T.P.I. CutterHead Feed Leadscrew will be powered with a variable speed 24VDC Motor driving it, so the Turntable Motor only has the single duty. Soulbear
- Tue Dec 02, 2014 12:08 pm
- Forum: Secrets of the Lathe Trolls
- Topic: Torque Requirements
- Replies: 2
- Views: 653
Torque Requirements
HI Everyone, Got a little query regarding Torque Requirements for my DIY Cutting Lathe Turntable. After several dead ends with respect of powerful motors (I think I may have gone a little overboard specification wise, some that I looked at would probably have raised the Titanic!!) At the risk of loo...
- Fri Nov 21, 2014 4:52 am
- Forum: Secrets of the Lathe Trolls
- Topic: Caruso Cutterhead
- Replies: 2
- Views: 776
Re: Caruso Cutterhead
Opcode66
Thanks for that info, now I just got to learn how to navigate SSoLT site and make sure my messages to Flo don't end up with me ordering a Piza from from China or a new Porsche from Germany by mistake!! SoulBear
Thanks for that info, now I just got to learn how to navigate SSoLT site and make sure my messages to Flo don't end up with me ordering a Piza from from China or a new Porsche from Germany by mistake!! SoulBear
- Thu Nov 20, 2014 9:04 am
- Forum: Secrets of the Lathe Trolls
- Topic: Caruso Cutterhead
- Replies: 2
- Views: 776
Caruso Cutterhead
HI All, A small enquiry that fellow Lathe Trolls may be able to help with. Is the Caruso CutterHead available to purchase on the open market, if so, can anyone Please Please post contact details. I've tried to make contact through Vinylike and Floka but had no response. The contact (if any?) was mad...
- Sun Nov 09, 2014 5:27 pm
- Forum: Newbie Forum
- Topic: Welcome, Newbies! Say Hi in this thread!
- Replies: 375
- Views: 600785
Re: Welcome, Newbies! Say Hi in this thread!
Hi to all Lathe Trolls, I'm Soulbear from Yorkshire, England & new to this forum and thought I had posted a quick introduction some little while back. Don't know what happened to my previous intro but can't seem to find it so I'm having another attempt. :roll: Don' know if any of the members or mode...
- Tue Nov 04, 2014 2:15 pm
- Forum: Newbie Forum
- Topic: Welcome, Newbies! Say Hi in this thread!
- Replies: 375
- Views: 600785
Re: Welcome, Newbies! Say Hi in this thread!
Just a quick Hi to all dedicated Lathe Trolls. I'm new to the forum but have been viewing from afar for a little while. Hope to bring a D I Y lathe build to fruition in the coming months, the real bogie for me is the cutter head design/setup. Any design tips-hints- project- know-how would be greatly...