The Secret Society of Lathe Trolls

Plastic pcf etc. is a bad material, corundum [sapphire, ruby] oxides are too soft, but possibly a diamond, but the effect will be poor, big noise, there's nothing you can do about it, who says otherwise let them do the recording on you tube and prove that it will be great ... Only lacquer master wil...

sound cutter head HX-10 SAKU REC 1165 TEST ACCELERATION LIM 2A pp BSB.mp3
so it will look like the head outside the HX-10
original photos in a few days

In this story, page, everyone can show their achievements, this thread is not restricted. Anyone can write, praise and criticize other achievements. Mr. Marct asked for help on the head T560, many times, but no one willingly answered. Only when Mr Marct opened the head, a few people took the floor o...

great solutions drive the lathes, the main shaft mounted on the ceiling, the belts, great machine! Great video recording, thank you very much for the film video !!!!!! This is the original factory Edison? :) [ you could mount the camera a small white LED, it would be exactly, more of everything see ]

old head hx-2 https://www.youtube.com/watch?v=HmTTlW9mf4s&feature=youtu.be

SAKU CUTTER HEAD HX-10 STEREO TEST , END SAKU PIC UP DST62
Amp power 2x250W RMS 4 ohm , Acceleration [ SAKU] Motorola MC1494 x4 Linear Four Quadrant Multiplier, 2Amp limit

DST62 SAKU

saku DST62 wire coil 0.01mm 100 ohm STEREO PIC UP

saku head mp3

SMusic

now I construct the head, I'm thinking that this just meet my expectations, heads on the speakers is black pudding [just for fun, amateur low-quality recordings, not mastering]
  a few days, everything will show the pictures, it cost me a little bit, but I think it will be worth it

Hi Mark[/quote] you're right ! I first check as head actually recorded on the disc, and only in the next stage, possibly checking a spectrum analyzer. other test method is erroneous and false , comforted only constructor, but it has nothing to do with truth and reality. In the open air, head exhibit...

nice machine

a lot depends on the original signal. I still Stockfish record , because that is my point of reference is the sound different sounds, voice, music, musical instruments, the sound of a vinyl record, the work of the German machine. I have some problems with the sound, it is 1.3 kHz - 35dB resonates at...

Sillitoe, the sound is sensational! What do you use to cut the head? I did a little analysis of this signal, in general there is no background noise plate, below 30 Hz and above 13 kHz? Correlation phase is excellent! The recording sounds just as good as the original recording! Im very impressed ! T...

Hello, beautiful lathe.
If you want I can translate you this instruction. You Scan instructions. Deposit only CONTRIBUTE The Secret Society Lathe Trolls for example 300 $ -400, . without instructions you can damage the lathe or cutting head
I do not want money.

Vestax cutter head vrx2000 min pipe dia 8,5 mm 12,5 kHz

hi, I think that is the same diameter as for me, that is 3.5mm, if it would be less in diameter, the side walls burst as a result of vibration and temperature knife 120 -150 C . A screw that secures the knife having a thread 1, 8 mm, lower diameter of the thread broke off :mrgreen: westrex pipe min ...

Sillitoe wrote:Hi Sakuszi,
Yes you can connect multiple boards.
Lots of possibilities.

Have an experiment...

Good luck!

Hi ,
thanks, it's good that there is a possibility extension of the control part, I have to look at this

Sillitoe, thanks for the link,
Tell me if this driver has inputs and outputs?
I need 24 control inputs and 12 outputs
If it does not meet my requirements I have to stay on Motorola MC14...