Search found 555 matches
- Tue Aug 20, 2019 2:11 am
- Forum: Classifieds & tip-offs
- Topic: Caruso Preamp Full Build Service
- Replies: 25
- Views: 4783
Re: Caruso Preamp Full Build Service
molex KK 254 series 2695 any KK series work 3pin part number 22013037 2pin part number 22013027 https://www.mouser.ch/datasheet/2/276/0022013037_CRIMP_HOUSINGS-158306.pdf you also need the crimp contacts. and a quite expensive crimp tool. but small flat pliers will do the trick. hapyp cutting f.
- Wed Aug 07, 2019 2:57 pm
- Forum: Classifieds & tip-offs
- Topic: wanted. for trade. ZS90/45 dead or alive.
- Replies: 1
- Views: 468
wanted. for trade. ZS90/45 dead or alive.
just in case someone has an old
today absolutely unuseable
neumann ZS90/45.
even in non working condition.
should be complete optically.
i will trade against a (working) caruso or a pitch13 controller.or a 16" vacuum platter.
thanks
f.
today absolutely unuseable
neumann ZS90/45.
even in non working condition.
should be complete optically.
i will trade against a (working) caruso or a pitch13 controller.or a 16" vacuum platter.
thanks
f.
- Tue Mar 12, 2019 11:19 am
- Forum: Classifieds & tip-offs
- Topic: Neumann AM32
- Replies: 3
- Views: 1123
Re: Neumann AM32
well not true anymore. if you do it nicely. thick mounting plate. rubber damping between mounting plate and linear slide then there is no more noise. of course you changed the 40-50 year old bearing and did a nice cleanup before.... there is also another verison of belt, pulley with round profile in...
- Tue Feb 12, 2019 5:20 pm
- Forum: Classifieds & tip-offs
- Topic: SOLD: VG66 cards
- Replies: 2
- Views: 625
GONE
GONE.
thanks i think cards are gone and found a happy user.
at my place they just had a non appreciated life in a dusty box.
happy cutting
f.
thanks i think cards are gone and found a happy user.
at my place they just had a non appreciated life in a dusty box.
happy cutting
f.
- Mon Feb 11, 2019 7:17 am
- Forum: Classifieds & tip-offs
- Topic: SOLD: VG66 cards
- Replies: 2
- Views: 625
SOLD: VG66 cards
hello i want to clear out some stuff i dont use anymore as i dont service VG66 racks anymore i throw out all my spare cards. there is 1x CE66LEFT 1x CE66RIGHT 1x FBamp 1x MonPreamp1 5x DRIVE AMP condition unknown. the FB card was recapped in 2016. so some are definitely useable. others need some lov...
- Tue Oct 16, 2018 5:15 pm
- Forum: Vinyl Mastering, Lacquer cutting, Pro's and others
- Topic: Neumann Disk Mastering products
- Replies: 9
- Views: 2887
Re: Neumann Disk Mastering products
hmm strange i did an update , as i accidently submitted unfinished. but it seems someone put it back to unfinished text.and i cna not edit last post. anyway. to moderator please better delete my full post than go back to unfinished post. but some adding note that can make confusion. vinylium never d...
- Mon Oct 15, 2018 2:52 pm
- Forum: Vinyl Mastering, Lacquer cutting, Pro's and others
- Topic: Neumann Disk Mastering products
- Replies: 9
- Views: 2887
Re: Neumann Disk Mastering products
patents lifetime is 20 years. if you pay every year your fees. and you pay for each country... so most companies just cover the important countries. so quickly a 200k$ bill for your patents every year... so think twice to make patents. so for neumann: all gone. and there where never aptents for the ...
- Wed Sep 19, 2018 9:09 am
- Forum: Vinyl Mastering, Lacquer cutting, Pro's and others
- Topic: scully 501/601 belt size
- Replies: 2
- Views: 1433
scully 501/601 belt size
hello a quick question about scully belt size from tilton. no access to manual right now and would be great to know it asap as we have to find some new ones. white (flywheel) : 1/2 x 81 2/3 red (45):1/2 x 76 ??? (unreadable the rest) green(33.3): unreadable.... thats the broken one. if someone has a...
- Thu May 24, 2018 9:58 am
- Forum: Secrets of the Lathe Trolls
- Topic: Vinylium Dub cutter, Urgent help needed please!
- Replies: 2
- Views: 610
Re: Vinylium Dub cutter, Urgent help needed please!
both switches are in parallel one side of the cable on one leg the other on the other leg. there are only 4 pins going from the mechanics to the Kingkong (the controler print. 2 are for the motor 2 for the end switch. if you send me an email flo (aet) floka (doet) com i can send you some more infos....
- Tue May 15, 2018 4:02 am
- Forum: Secrets of the Lathe Trolls
- Topic: Caruso Head
- Replies: 12
- Views: 3288
Re: Caruso Head
i dont want you to encourage to upgrade your wonderfull vr system but if you want to play away from home here a small step to step guide. ******************************************************* for an upgrade you need: - dump the original electronics. or use as a doorstopper. i know its hard to send...
- Wed Mar 21, 2018 10:09 am
- Forum: Newbie Forum
- Topic: dmm vs acetate and...levels
- Replies: 3
- Views: 947
Re: dmm vs acetate and...levels
i did dmm cutting for more than 10 years. and everything i liked on laquer cutiing i did not have on dmm. i modified mine to cut even deeper but still i did not like. then i converted bac kto lacquer. but today there is reason to use dmm and also hope to get nice cuts. the SAL84 is the end of neuman...
- Wed Mar 21, 2018 9:49 am
- Forum: Experimenters' & Innovators' forum
- Topic: Caruso Pre-Amp Schematics
- Replies: 10
- Views: 2182
Re: Caruso Pre-Amp Schematics
i think sorted out. the boards will be out in a few days. there are always boards. new version. ready to ship. a few leftovers from the older version.. i finally have full built & tested boards on stock . (and matched pairs on request). sending an email with: - subject "i like to order xxxxx (whatev...
- Tue Feb 13, 2018 7:14 pm
- Forum: Classifieds & tip-offs
- Topic: Neumann VG66 Cutting Amplifiers
- Replies: 14
- Views: 2859
Re: Neumann VG66 Cutting Amplifiers
hmm. must be expensive if it says neuann. vg66 is for museum use only. dont buy if you want to cut serious masters. except you want that vg66 sound.weak bass . no transparency and everyting passing 50 year old electrolytic caps. yammi! the main power amps are a super early transistor design. with bi...
- Wed Dec 20, 2017 7:46 am
- Forum: Classifieds & tip-offs
- Topic: SX74 wanted
- Replies: 2
- Views: 762
Re: SX74 wanted
please make reasonable offer to
flo {at} floka {dot} com
no p.m. on this forum please
if i can't refuse, i can let one go.
my cutterheads always serviced, checked with all tests and and charts.
flo {at} floka {dot} com
no p.m. on this forum please
if i can't refuse, i can let one go.
my cutterheads always serviced, checked with all tests and and charts.
- Wed Nov 22, 2017 3:50 am
- Forum: Secrets of the Lathe Trolls
- Topic: Vinyl Recorder in the future
- Replies: 10
- Views: 1781
Re: Vinyl Recorder in the future
and i heard you can even get BASS.
i mean real BASS recorded with your VR
i mean real BASS recorded with your VR
- Thu Nov 09, 2017 5:17 pm
- Forum: Vinyl Mastering, Lacquer cutting, Pro's and others
- Topic: caruso infos. new link
- Replies: 4
- Views: 3941
caruso infos. new link
hello unfortunately the vinylike.de site took a french leave. so all info's was gone too. but vinylike.com is still around. here again the most important stuff. will put more stuff whenever i find a minute. check from time to time. but most you need is there. also a video about calibration and some ...
- Tue Nov 07, 2017 6:29 pm
- Forum: Classifieds & tip-offs
- Topic: Flokason test record finally out for sale.
- Replies: 6
- Views: 2517
Re: Flokason test record finally out for sale.
b-side is same as a side. but different lacquer & stamper.same cutting session.same galvanic session link will follow. not in my hands... and yes i work on volume 2. with fixed freq. bands. but true mono. and at least a 5minute 1k tone haha.maybe a full side! for volume 1 around 10 iterations. cutti...
- Wed Sep 27, 2017 10:48 am
- Forum: Classifieds & tip-offs
- Topic: Flokason test record finally out for sale.
- Replies: 6
- Views: 2517
Flokason test record finally out for sale.
long time only through unofficial channels. now here with a nice cover. and its the same content as the new ortofon one. so prooved by the experts. http://www.flokason.ch/imgs/flokasontesttone_record001s.jpg the content: http://www.flokason.ch/imgs/flokasontesttone_record001_content.jpg link for the...
- Sat Aug 19, 2017 7:02 am
- Forum: Vinyl Mastering, Lacquer cutting, Pro's and others
- Topic: Neumann console upgrade and replacements
- Replies: 5
- Views: 2377
Re: Neumann console upgrade and replacements
if you can wait until beginning of the year. fully booked out until end of the year. check: http://www.flokason.ch/fs_flokason_gear.html around 6k or http://www.vinylium.ch/platform/content/element/40/master-control-front_xl.jpg around 18k also 4 channel monitor controllers and everything you need t...
- Fri Dec 23, 2016 3:54 pm
- Forum: Classifieds & tip-offs
- Topic: LATHE FOR CUTTING MASTERS?
- Replies: 8
- Views: 2427
Re: LATHE FOR CUTTING MASTERS?
hello Jonas well there is definitely a solution. so far there where still enough neumanns or scullys around to upgrade. and scullys where damn cheap if not fully working. the low end starts at around 15k euro. but leaves every scully behind ( except the look of course. cant beat that scully look). a...