The Secret Society of Lathe Trolls

I would go very slow.cut some stuff you know and where you have the master and a reference on vinyl. listen on a decent system you know.compare and and do slight adjustments.. the fab filter .pink noise is the wrong way to go. Technically yes .but soundwise very bad idea… You don’t have to dream. Ca...

the original target lathe of caruso head back in the day was not a neumann. more for simpler smaller lathes often with less space. so i made a 8mm bar not 10mm . but its hold by 3 standard M3 screws. so take a little longer screws and it does not matter if its 8 or 10mm bar. if you want a 18mm round...

hello lathetrolls
someone asked me about possibility of very thin 1980 style maxi single pressings in the range 110-120 grams.
yes against any trend i know.
who can do that?

happy cutting f.

Len is your man if it comes to original westrex…no one knows this stuff better. If not successful I can offer a dialba head and vc200 amps.. sounds damn good and is very close to 1700 specs.. i have to look up W1700 rail to rail Voltage.but you will get louder cleaner cuts than with a 3D head… The o...

i think its very easy to find out. this should maybe go to a general buyers guide for cutting equipment. just send in a few music samples and ask for a cut on the actual particular machine that you are looking to buy. any serious seller, will cut it and send it for reasonable amount of money. pay fo...

hello Mark
the premotec was just laying around... not the reference.
and it only works with belt driven TT's as they dont run stable on direct.

but if you go the belt way you find cheap some bldc with electronics for 30-50$ esy
happy cutting
f.

There is TZO in Leipzig as only independent manufacturer at the moment..hopefully more to come. Most factories do the blanks themselves.

hello Steve thanks for the update. a few additional infos poland: optical disc mastering. https://opticaldiscmastering.eu/ on the first all new built dmm lathe (flokason AM44 dmm lathe with ultracut amps) germany: -emil berliner is not yet in operation as far as i know. they have the lathe but i hav...

Make me a reasonable offer and it is yours
As is.coil ok movement ok

From a client.
2x sx74 heads great condition .all original
Alle tested.charts

nice find! thanks for sharing.
happy cutting. f.

Replace your lyrec and all is fine….:) I would go with the thickest gear oil for Oldtimers Or maybe fill it with some Polyurethane or silicone 2k Material... No more oil mess . this is 1920 technology and I guess we have some possibilities hundred years later Also a good time to think about modern c...

i think he is in front of a coil winder.
but looks great.

when i was there around 1998 there where at least: arrows : 1 scully (upgraded with the first pitch98 prototype) 3x presto 6n with grampian head for direct dubplates. with homemade preamps dynamic sounds: vms70 in bad shape but workable tuff gong: non working vms70 havent seen more studios at the ti...

just for everyone who is interested in a pitch controller or any other flokason goodies. best buy it directly. then you will get best support. if you buy 2nd hand we can and do support of course but taxometer will turn on usual rate. also we provide all the necessary breakout boards, goodies tricks ...

the official dmm document dated 15.04.1984 says: 100um +/-10 um.
***********************
happy cutting. f.

yes scheffner might be the only alternative at the moment to a FLoKAson AM44. (if you watch carefully the connaisseur will recognize is a lot of flokason technology built around...) of course if you just want plastic you might one of the lucky souri cutter customers (with very hard filtered ,custome...

just in case someone wants to grab one of the last caruso head we have. this is your chance.
buy that ES59. swap it with a caruso+ 2 preamps.
happy cutting. f.

I think I finally found it…can you send me a email?not pm here so I can forward picture
Thanks

i might have one i will check when back home ...i definitely dont need it anymore